Jrk 21v3 USB Motor Controller with Feedback

Pololu item #: 1392
Brand: Pololu supply outlook
Status: End-of-Life Rationing 
RoHS 3 compliant

Price break Unit price (US$)
1 69.95
5 64.35


backorders allowed

The Jrk 21v3 motor controller is a highly configurable brushed DC motor controller that supports four interface modes: USB, logic-level serial, analog voltage, and hobby radio control (RC). The controller can be used with feedback for closed-loop speed or position control, or it can be used without feedback as an open-loop speed control. The continuous output current is approximately 3 A in the recommended operating range of 8 V to 28 V, with derated performance down to 5 V and transient protection to 40 V. This version ships with connectors included but not soldered in, allowing for custom installations.

Alternatives available with variations in these parameter(s): version Select variant…

 Description Specs (16) Pictures (23) Resources (11) FAQs (2) On the blog (4) 
Why is the Jrk not driving my motor?
There might be an error preventing the Jrk from driving the motor; check the Errors tab in the configuration utility. If you are trying to use a feedback mode, make sure that you have entered some non-zero PID constants (good starting values are Proportional=1, Integral=0, Derivative=0) and make sure there is a large difference between the values of the Target and Feedback variables. If you are trying to use the no-feedback (speed control) mode, then make sure that the target is not close to 2048 (speed 0); try setting the target to 2648 (full speed forward). In either case, you should look at the graph and make sure that the Duty Cycle is not close to 0; try to get it closer to +600 or -600 (full speed forward or full speed reverse).
Does the Jrk support using a quadrature encoder for feedback?
The Jrk motor controllers do not work with encoders, in the sense that you cannot get position control over unlimited number of rotations. (The Jrks are typically used with potentiometer feedback, which allows for up to a few rotations when using multi-turn potentiometers.)

Related Products

Jrk G2 21v3 USB Motor Controller with Feedback
Jrk G2 21v3 USB Motor Controller with Feedback (Connectors Soldered)
Jrk G2 18v19 USB Motor Controller with Feedback
Jrk G2 24v13 USB Motor Controller with Feedback
Jrk G2 18v27 USB Motor Controller with Feedback
Jrk G2 24v21 USB Motor Controller with Feedback
Jrk 21v3 USB Motor Controller with Feedback (Connectors Soldered)
Jrk 12v12 USB Motor Controller with Feedback
RoboClaw 2x15A Motor Controller (V6B)
Thin (2mm) USB Cable A to Mini-B, 5 ft., Low/Full-Speed Only
USB Cable A to Mini-B, 5 ft
Glideforce LACT10P-12V-20 Light-Duty Linear Actuator with Feedback: 50kgf, 10" Stroke (9.8" Usable), 0.57"/s, 12V
MC33926 Motor Driver Carrier
i00600 Torxis Servo 1600 oz.in. 1.5 sec/90 deg
Micro Maestro 6-Channel USB Servo Controller (Assembled)

Related Categories

Pololu Jrk Motor Controllers with Feedback
Motors and Gearboxes
Linear Actuators
Glideforce Light-Duty (LD) Linear Actuators
Premium Jumper Wires
Wires with Pre-Crimped Terminals
Pololu Simple Motor Controllers
Development Boards (Programmable Controllers)
RC Interface
Log In
Pololu Robotics & Electronics
Shopping cart
(702) 262-6648
Same-day shipping, worldwide
Menu
Shop Blog Forum Support
My account Comments or questions? About Pololu Contact Ordering information Distributors